Traverse's 2011 s13 hatch build started (JAN 2010 to present)

[Shift_RHD]

Yeah this car is gona be bomb. I saw it the day I picked up a few parts from Ray. Super clean.

[s13slideways]

bled the clutch and brakes tonight also made a coolant reservior tomorow gona make a matching power strearin. might as well right. got most of the wiring sorted out for the interior along with the kill switch and guages. just need to get a small switch panel to run a few things. also got the last round of an fittings and weld on stuff ordered today to make the oil catch can and reserviors. Nomex braided hose should be here sometime this week and i can start finishing the plumbing all off. also got the swirl pot mounted and all the fittings arranged for the setup. just need to get some high temp blue silicone hose to run all the line. also welded the hood hinges so they stay at a fixed height so i can mount another hood pin set from that point and keep the vented hood look. lots of progres busting ass to get out there next week. getting the power fc this friday when jason gets back in town. everything else is small shit that i should be able to work out. the biggest thing is the tune if im gona have the time to get it done. might need a local quickie tune for the event see. lol well see

[DRTYM30]

your welcome traverse

[s13slideways]

your welcome traverse

thanks alot garret for pumping that peddle up. lol

[s13slideways]

here are dsome more updates as of now still waiting on fittings and nomex hose. heres a baller little overflow catch tank for the swirl pot setup. forrest is getting down on the aluminum weldings. also got the big ass fuel filter and fuel pressure regulator mounted so that all the lines can be made.


also modified the circuit sports overflow to be a swirl pot and added mounting tabs to relocate it. thanks garret for practicing on that for me. also made it all 1/8 npt slip on fittings for the overflow system. just waiting on that hks blue silicone hose.

Made a coil pack cover out of aluminum with some dimmple madness. really stoked on how it turned out gona start producing these and different styles if any one likes it. lmk. also got the lil greddy dildo in place in the waterline for the temp guage. thanks eugene. and thanks again garret for sautering that sensor for me.

started runing the interior harness and guages etc. just waiting on my power fc to finish up the wiring and should have that this weekend.

hope i can make it im pushing hard more all nighters and broke pockets to come but its worth every penny.

[s13slideways]

all work and no play jack grows a dull boy. some stress relieving in drifters paradise.

http://s854.photobucket.com/albums/ab107/drivinhrd300zx/?action=view&current=Video_062710_001.mp4	Small | Large

http://s854.photobucket.com/albums/ab107/drivinhrd300zx/?action=view&current=Video_062710_0041.mp4	Small | Large

[s13yaobling]

hella baller man. Forest really gets down on those aluminum weldings. GL to you, hope you make it out in time.

[s13slideways]

got a seat finally thanks to iced tea and also got alot more bolted on and in its finished location. more wiring nightmares that im going over and waiting on more AN fitttings and braided hose should be here today up until wednesday. then all i need is to pay off my power FC and its ready to start. gona be close but will make round four 100 percent for sure. post more pics when i get the hose today and make all the lines

[s13slideways]

more updates just waiting on some stuff gona make sure its done right the first time.
got the intake pipe made, power stearing reservior, ran most of the fuel lines, oil lines and coolant lines with an fittings, nomex and ss hose. got the BMC heat shield on, wraped the downpipe and dump tube. lots of stuff going on still.


got both of my seats finaly

started doing the alignment and pulling out more angle!!  love the enkies on my car

need to lower the car more its 4x4 status right now. enkies are dope and so light

power stearing reservior and 4" intake

most of the plumbing done waiting on a few things to finish it up

re-mounted oil cooler and did all the lines

overhead of motor with led strips lite up in there hidden spots.
 thats all for now waiting on like 3 fittings and coolant and vacum hose to finish off plumbing and paying off the power fc from my buddy, and a switch panel to finish off the wiring. most likely gona try to have frank from BOSO GARAGE tune the setup when they come down here for FD Las Vegas. so if anyone wants some tuning done by a legendary tuner let me know im trying to get at least 2 other people to make sure its worth there time to bring the dyno packs and equipment. pm me for more info thanks

[Dook-E]

you should make one of those coilpack covers for an S14 SR and i should buy it from you.

car is looking great man, hopefully we will see you out at Round 4.

[s13yaobling]

ooooo pretty lights! lol. car is looking better and better. cant wait to see it out there.

[s13slideways]

you should make one of those coilpack covers for an S14 SR and i should buy it from you.

car is looking great man, hopefully we will see you out at Round 4.

if u want a coil cover pm me i can make one for sure if u want in different dimple styles too.

thanks yao. i cant wait either.

[DRTYM30]

traverse capitalizing on my dimple coil cover ideas

[Dook-E]

you should make one of those coilpack covers for an S14 SR and i should buy it from you.

car is looking great man, hopefully we will see you out at Round 4.

if u want a coil cover pm me i can make one for sure if u want in different dimple styles too.

thanks yao. i cant wait either.

will you need the valve cover to mock it up since it's shaped different than the S13 SR cover? cuz the motor and shit isnt here yet.

[s13slideways]

ya would need the cover i dont have a notch top cover laying around. pm me and we can figure it out if u r interested in a cover